LEVITON DOS02 QUICK START MANUAL Pdf Download (2024)

Ratings: 120VAC, 60Hz 250 W Incandescent, 2 A Resistive, 150W LED and CFL, 250 VA ELV, 200VA MLV

WARNINGS

• TO AVOID FIRE, SHOCK OR DEATH: TURN OFF POWER AT CIRCUIT BREAKER

OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!

• TO AVOID PERSONAL INJURY OR PROPERTY DAMAGE, DO NOT install to

control a receptacle, or a load in excess of the specified rating.

• To be installed and/or used in accordance with electrical codes and regulations.

• If you are not sure about any part of these instructions, consult an electrician.

Features

• Cat. Nos. DOS02 and DVS02 have a sensing angle of 180° and a

sensing area of coverage of 30 x 30 ft. See coverage diagram for details.

• Adjustable ambient light (DOS02 only), time delay and area of coverage

controls. See adjustment setting section for details.

• Indicator light alerts the user of device status.

• Adjustable time delay setting for 1, 5, 10 and 20 minutes plus a test mode

with 5 seconds on. A Temporary Bypass mode that disables the Auto-on

feature is available only for DOS02.

Mounting Location

The device responds to temperature changes and care should be taken

when mounting the device.

• DO NOT mount directly above a heat source, in a location where hot or

cold drafts will blow directly on the sensor, or where unintended motion

(e.g., hallway traffic) will be within sensor's field-of-view.

You Will Need:

• Slotted/Phillips screwdriver

• Electrical tape

• Cutters

• Pliers

Installation

WARNING: TO AVOID FIRE, SHOCK OR DEATH, turn off power at circuit breaker or

fuse and test that the power is off before wiring.

1. Identify your wires

(most common):

NOTE: Neutral wire (if present), or a Ground wire is required for operation. If

the wiring in the wall box does not resemble this configuration, consult an electrician.

LINE

GROUND

OR

LOAD

2a. Wire (when Neutral is NOT present).

Working on one connection at a time, connect wires as shown.

NOTE: This device is designed so the line and load wires can be wired

interchangeably.

LINE/LOAD

(Black)

GROUND

(Green

sleeved

wire)

LINE/LOAD

(Black)

GROUND

(Green/Yellow)

Single Pole Wide View Motion Activated Light Control

Cat. Nos. DOS02, DVS02 - INDOOR USE ONLY

LINE

GROUND

NEUTRAL

GROUND

LOAD

LINE

GROUND

LOAD

CAUTIONS

• To clean use a damp cloth with mild soap. DO NOT use disinfecting products,

including foggers, sprays or other types of atomized cleaning agents.

• No user serviceable components. DO NOT attempt to service or repair.

• Use this device WITH COPPER OR COPPER CLAD WIRE ONLY.

INSTALLATION

2b. Wire (when Neutral is present).

Remove the Green sleeve from the White wire. Working on one connection at a

time, connect wires as shown.

NOTE: This device is designed so the line and load wires can be wired

interchangeably.

NEUTRAL

(White)

LINE/LOAD

(Black)

3. Test and mount.

• Restore power. Wait 10-20 seconds for sensor to power up.

• DOS02: Lights will automatically turn ON with first motion seen after warm up

period, or when push pad is pressed.

• DVS02: Lights will turn ON when push pad is pressed.

NOTE: If lights do not turn ON, refer to the "What to do if..." section.

Turn off power at circuit breaker before completing the installation.

• Gently push wires into wall box. Screw light control to box.

• Install wallplate.

• Restore power.

Operation

RED indicator light

(Will flash any time

motion is detected)

TOP of button

NOTE: Press either

TOP or BOTTOM of

button to turn ON/OFF.

Programming

1. How to change the settings.

In order to...

Enter programming

mode

Change settings

(Timer, Sensitivity,

Ambient Light)

Change options

within a setting

Save and exit

settings

NOTE: If there is no activity for 30 seconds, the device will automatically exit

programming mode and setting changes will not be saved. Multiple settings can be

saved by entering the programming settings once, selecting desired settings and then

saving and exiting.

Setting Types and Options (defaults are in bold)

Setting 1

TIMER

(Duration of time

Option

for which load

Number

is ON since last

detected motion)

Option 1

1 minute

Option 2

5 minutes

Option 3

10 minutes

Option 4

20 minutes

LINE/LOAD

(Black)

LINE

LOAD

GROUND

(Green/Yellow)

BOTTOM of button

How to choose a setting and option

Do this...

Indicator light will...

GREEN light will be solid ON for 5 seconds

Hold TOP and BOTTOM

NOTE: If nothing happens, device is already in

button for 5 seconds

programming mode

Single press TOP button

RED light will blink to indicate setting selected

= advance to the next

(Timer ->Sensitivity ->Ambient Light ->Timer)

setting (see table below)

(Example: Setting 1 = 1 blink/sec)

Single press BOTTOM

GREEN light will blink to indicate option selected

button = advance to the

(Option 1 ->Option 2 ->Option 3 ->Option 1)

next option

Examples: Option 1 = 1 blink/sec

(see table below)

Option 2 = 2 blinks/sec

Hold either TOP or

BOTTOM button for

GREEN light will be solid ON for 5 seconds

5 seconds

Setting 2

SENSITIVITY

(Sensitivity to motion –

adjusting the major and

minor detection range.)

Low (50% Range)

Medium

High

All settings to default

PK-A3345-10-00-2A

ENGLISH

NEUTRAL

GROUND

GREEN locator/

indicator light

(Turns ON when

load is OFF)

Setting 3

DOS02 only -

AMBIENT LIGHT

(If the room is brighter

than the setting selected,

the load will not turn ON.)

Low Light level

Medium Light level

High/Brightest light level

Disabled – turns ON for all

light levels

LEVITON DOS02 QUICK START MANUAL Pdf Download (2024)

References

Top Articles
Latest Posts
Article information

Author: Fredrick Kertzmann

Last Updated:

Views: 5477

Rating: 4.6 / 5 (46 voted)

Reviews: 93% of readers found this page helpful

Author information

Name: Fredrick Kertzmann

Birthday: 2000-04-29

Address: Apt. 203 613 Huels Gateway, Ralphtown, LA 40204

Phone: +2135150832870

Job: Regional Design Producer

Hobby: Nordic skating, Lacemaking, Mountain biking, Rowing, Gardening, Water sports, role-playing games

Introduction: My name is Fredrick Kertzmann, I am a gleaming, encouraging, inexpensive, thankful, tender, quaint, precious person who loves writing and wants to share my knowledge and understanding with you.